| Decision area<\/th>\n | Define before quotation<\/th>\n | Evidence to request<\/th>\n<\/tr>\n<\/thead>\n |
|---|---|---|
| Soil type<\/td>\n | Dust, flux, oil, adhesive or mixed residue<\/td>\n | Identify contamination before choosing chemistry<\/td>\n<\/tr>\n |
| Material compatibility<\/td>\n | Resin, additive, coating and label system<\/td>\n | Use supplier guidance and coupon trials<\/td>\n<\/tr>\n |
| Cleaning process<\/td>\n | Wipe, wash, rinse, dry and handling<\/td>\n | Control tools, solution and sequence<\/td>\n<\/tr>\n |
| Release check<\/td>\n | Visual, particulate, residue and functional criteria<\/td>\n | Document acceptance and lot status<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n Use the table as an RFQ discussion guide, not as a substitute for controlled values. Final limits should come from current device drawings, equipment interfaces, the facility ESD program, supplier documentation and qualified trials. When a number is not yet known, state the functional risk and agree a prototype test instead of copying a limit from an unrelated tray.<\/p>\n For jedec tray cleaning, the buyer must define dust, flux, oil, adhesive or mixed residue<\/strong>. This point controls whether the tray can clean reusable trays without damaging pockets, changing surface behavior or leaving residue that can reach devices. Write the requirement against the actual device, route and equipment rather than a generic tray description. Name the responsible drawing or work instruction, the condition in which the characteristic applies, and who approves an exception.<\/p>\n The practical verification is to identify contamination before choosing chemistry<\/strong>. Begin with identified samples from the proposed production material and tooling. Record sample quantity, lot or cavity, conditioning, equipment, method and result. Include both normal and credible worst-case conditions. A pass on one convenient sample is useful for development, but it is not evidence that production variation is controlled.<\/p>\n Ask the supplier to explain which input variables can change this result. Depending on the characteristic, these may include resin or sheet lot, additive level, molding or forming settings, cooling, trimming, storage, cleaning and previous use. Convert important variables into incoming evidence, periodic checks or formal change notification. This makes the requirement auditable and prevents a catalog promise from becoming the only acceptance basis.<\/p>\n For jedec tray cleaning, the buyer must define resin, additive, coating and label system<\/strong>. This point controls whether the tray can clean reusable trays without damaging pockets, changing surface behavior or leaving residue that can reach devices. Write the requirement against the actual device, route and equipment rather than a generic tray description. Name the responsible drawing or work instruction, the condition in which the characteristic applies, and who approves an exception.<\/p>\n The practical verification is to use supplier guidance and coupon trials<\/strong>. Begin with identified samples from the proposed production material and tooling. Record sample quantity, lot or cavity, conditioning, equipment, method and result. Include both normal and credible worst-case conditions. A pass on one convenient sample is useful for development, but it is not evidence that production variation is controlled.<\/p>\n Ask the supplier to explain which input variables can change this result. Depending on the characteristic, these may include resin or sheet lot, additive level, molding or forming settings, cooling, trimming, storage, cleaning and previous use. Convert important variables into incoming evidence, periodic checks or formal change notification. This makes the requirement auditable and prevents a catalog promise from becoming the only acceptance basis.<\/p>\n For jedec tray cleaning, the buyer must define wipe, wash, rinse, dry and handling<\/strong>. This point controls whether the tray can clean reusable trays without damaging pockets, changing surface behavior or leaving residue that can reach devices. Write the requirement against the actual device, route and equipment rather than a generic tray description. Name the responsible drawing or work instruction, the condition in which the characteristic applies, and who approves an exception.<\/p>\n The practical verification is to control tools, solution and sequence<\/strong>. Begin with identified samples from the proposed production material and tooling. Record sample quantity, lot or cavity, conditioning, equipment, method and result. Include both normal and credible worst-case conditions. A pass on one convenient sample is useful for development, but it is not evidence that production variation is controlled.<\/p>\n Ask the supplier to explain which input variables can change this result. Depending on the characteristic, these may include resin or sheet lot, additive level, molding or forming settings, cooling, trimming, storage, cleaning and previous use. Convert important variables into incoming evidence, periodic checks or formal change notification. This makes the requirement auditable and prevents a catalog promise from becoming the only acceptance basis.<\/p>\n For jedec tray cleaning, the buyer must define visual, particulate, residue and functional criteria<\/strong>. This point controls whether the tray can clean reusable trays without damaging pockets, changing surface behavior or leaving residue that can reach devices. Write the requirement against the actual device, route and equipment rather than a generic tray description. Name the responsible drawing or work instruction, the condition in which the characteristic applies, and who approves an exception.<\/p>\n The practical verification is to document acceptance and lot status<\/strong>. Begin with identified samples from the proposed production material and tooling. Record sample quantity, lot or cavity, conditioning, equipment, method and result. Include both normal and credible worst-case conditions. A pass on one convenient sample is useful for development, but it is not evidence that production variation is controlled.<\/p>\n Ask the supplier to explain which input variables can change this result. Depending on the characteristic, these may include resin or sheet lot, additive level, molding or forming settings, cooling, trimming, storage, cleaning and previous use. Convert important variables into incoming evidence, periodic checks or formal change notification. This makes the requirement auditable and prevents a catalog promise from becoming the only acceptance basis.<\/p>\n Approve the proposal in gates. First review the device revision, orientation, allowed contact, route, equipment and packaging stack. Next inspect identified first articles and verify the four decision areas above. Then load representative minimum and maximum devices, build the real stack, apply covers or restraints, and run the normal handling sequence. Include cleaning, heat, labels, storage and shipment only where they belong to the actual route.<\/p>\n Keep the approved drawing, material or construction identity, sample lot, photographs, raw results, deviations and sign-off together. Receiving inspection should check identity before sampling, separate lots, inspect critical features with the approved datum and method, and quarantine failures before they mix with accepted inventory. Sampling depth follows risk and supplier history; it should not be invented in a blog or purchase note.<\/p>\n This shortcut can release trays that look acceptable but fail during handling. Contain the affected lot, identify where the assumption entered the specification, and compare the tray with the controlled device and process requirements. Repeat the relevant dimensional, functional or electrical check under documented conditions. Record the disposition so the same issue can be recognized at receiving and during reuse.<\/p>\n This shortcut can release trays that look acceptable but fail during handling. Contain the affected lot, identify where the assumption entered the specification, and compare the tray with the controlled device and process requirements. Repeat the relevant dimensional, functional or electrical check under documented conditions. Record the disposition so the same issue can be recognized at receiving and during reuse.<\/p>\n This shortcut can release trays that look acceptable but fail during handling. Contain the affected lot, identify where the assumption entered the specification, and compare the tray with the controlled device and process requirements. Repeat the relevant dimensional, functional or electrical check under documented conditions. Record the disposition so the same issue can be recognized at receiving and during reuse.<\/p>\n Start the commercial discussion from SWESD\u2019s IC tray product page<\/a>. For adjacent decisions, consult the JEDEC tray dimensions guide<\/a>, custom IC tray RFQ guide<\/a> and semiconductor shipping tray guide<\/a>. These pages support planning; the controlled project documents remain decisive.<\/p>\n This neutral manufacturer video explains electrostatic-discharge fundamentals. It is supplementary and does not set project-specific tray limits.<\/p>\n |
![\"jedec](\"https:\/\/swesd.com\/wp-content\/uploads\/2026\/03\/BGA13x13.jpg.webp\")
![\"jedec](\"https:\/\/swesd.com\/wp-content\/uploads\/2026\/03\/BGA8x8.jpg.webp\")
![\"jedec](\"https:\/\/swesd.com\/wp-content\/uploads\/2026\/03\/QFN5x5.jpg.webp\")